Car Parts
Online Catalogue
Main Page
Watch USER'S Ratings
FORUM
 
Audi 80/90/Avant, year - 1992
Page:   BLOWER / HEAT EXCHANGER
«« Previous illustration  Return to group list   Next illustration »»

For security measures, illustrations and partnumbers are shown only to registered users.

To register, as a new user or merchant  

Partlist:

blower
heat exchanger
/
air distribution housing
lhd /
lever for temperature regulating flap
/
air distribution housing
rhd /
no longer available
lhd /
air duct
lhd /
air duct
rhd /
heat exchanger
lhd /
heat exchanger
rhd /
gasket
810X25X6 /
gasket
680X8X10 /
blower
lhd /
blower
rhd /
snap nut
M6X19,5X18 /
clips
/
clips
/
series resistor
lhd /
series resistor
rhd /
footwell vent
lhd /
footwell vent
rhd /
snap nut
M5X21X15 /
oval head panel screw
B4,2X9,5 /
oval hd. csk. self-tapp. screw
B4,2X13 /
hexagonal head bolt
M5X15SZ /
hexagonal nut
M6 /
double grommet
/
intake manifold
lhd /
intake manifold
rhd /
gasket / intake manifold
lhd /
gasket / intake manifold
rhd /
water hose
feed / 4 cylinder
water hose / (flange > heat exchanger) / F >> 8A-L-075 396
feed / 5-cylinder
water hose / (flange > heat exchanger) / F 8A-L-075 397>>
feed / 5-cylinder
water hose / (flange > heat exchanger)
feed / diesel eng.: 1Y
water hose / (flange > heat exchanger)
lhd return / diesel eng.: 1Y 4 cylinder
water hose / (flange > heat exchanger)
return / 5-cylinder
pipe clip
AL16-28 /
pipe clip
AL23-35 /
double stud with hexagon drive
M6X18/M6X15 /
hexagon nut, self-locking
AM6 /
sealing cord in coils of 10m 'order unit 1'
/
sealing cord
10X2MM /
foliage grille
/

Last forum topics about this model
I have an old Audi 80 - year model 1987 - still going strong, but I have one problem:

Sometimes - usually after driving more than an hour - it refuses to start again. It doesn't make any sound.

Then after maybe half an hour it starts normally.

It is quite unpleasant because I have no idea, why it does that ( =doesn't start)

I have a new starter, new cables to the starter, new ignition key system...

After replacing practically everything between the ignition key and the starter motor I found a relay, which is called "relief terminal relay".

Somebody told me that it is also so called x-contact relay, which has many purposes.

Could anybody tell me the meaning of this relay?

Could it be the cause for that mysterious starting problem?

It would be nice know if somebody else has had this problem...

Posted by hangab (Finland) 2008-09-04 22:22:35 AUDI Audi 80/90/AvantComments: 2, last 2008-11-17 12:38:46Open thread »»

Hi!
I have problem.
I cannot open my rear door using the handle.
The handle is not tensed anymore and it is soft(you can pull in order to open the trunck but with no result)

I put out the inner door ornament in order to see the mechanism.
Now... my big problem is... how should it be correctly assebled?
I looked on http://www.vagcat.com/epc/cat/au/A80/1994/150/56/1612769/ but i did not understand much.

Can you give me some info about what should i do to repair it?

Thanks!
razvan.c.radulescu@gmail.com

Posted by rcrazvan (Romania) 2008-08-22 20:14:30 AUDI Audi 80/90/AvantNo comments yet ...Open thread »»

Hi to you all. I hope somebody can help me? My Audi is a 1994 model 80 TDi.
The speedometer has stopped registering mileage done. Can someone tell me which sensor I need to replace and where is it situated? This is a fantastic site, I only wish it could add where some of the elusive parts are on the car. I thank you all in advance.
Johnro

Posted by johnro (United Kingdom) 2008-08-21 02:13:38 AUDI Audi 80/90/AvantComments: 2, last 2008-08-23 19:28:11Open thread »»

Where can I find a Non-return valve?
Pierburg Part#: 041.906.291.A

Posted by shogun (United States) 2008-08-05 03:04:56 AUDI Audi 80/90/AvantNo comments yet ...Open thread »»

Hi, I have an Audi 80 -94, with a few problems related to the cooling system:

1. The water in the expansion tank is completely cold even after 30 minutes of driving (not sure when this problem started). The radiator seems to have normal temperature.

2. Also the warning lamp is flashing all the time (this appeared a few days ago).

3. The fan always run when the ignition is on (these has been a fact for a year or so). I believe I should just exchange the thermo-switch?

I have an oil temp meter saying it's about 70C (158F 431K) and when touching the engine it seems to have normal temperature.

So it's probably two different faults (or maybe three). I tried yesterday to exchange the expansion tank, with the water level switch, with no success.

Regards Magnus

Posted by BlombergM (Sweden) 2008-03-08 17:12:16 AUDI Audi 80/90/AvantComments: 2, last 2008-03-10 10:07:22Open thread »»