Car Parts
Online Catalogue
Main Page
Watch USER'S Ratings
FORUM
 
Audi 80/90/Avant, year - 1987
Page:   WIRING HARNESS: FRONT RIGHT / / / 5 cylinder: / NG,PS
«« Previous illustration  Return to group list   Next illustration »»

For security measures, illustrations and partnumbers are shown only to registered users.

To register, as a new user or merchant  

Partlist:

wiring harness: front right / 5 cylinder:
1 (why hidden?)
wiring harness: front right / F >> 89-H-520 000
lhd / NG,PS NG
wiring harness: front right / F 89-J-100 001>> 89-J-520 000
lhd / NG
wiring harness: front right / F 89-K-000 001>>
lhd / NG
wiring harness: front right / F 89-J-100 001>> 89-J-520 000
lhd / PS
wiring harness: front right / F 89-K-000 001>>
lhd / PS
wiring harness: front right / for vehicles with / anti-knock sensor / F 89-J-100 001>> 89-J-520 000
VEZ lhd / PS
wiring harness: front right / for vehicles with / anti-knock sensor / F 89-K-000 001>>
VEZ lhd / PS
wiring harness: front right / F 89-J-100 001>> 89-J-520 000
rhd / PS
wiring harness: front right / F 89-K-000 001>>
rhd / PS
cable tie
4,5X200 /
cable tie
10X128 /
protective cap
39X7,5 /
grommet
18X20,5 /
flat contact housing
3 pin /
flat contact housing / connecting part / thermo time switch / temperature sender / valve / lambda probe / switch / brake fluid
2 pin NTC AKF heater /
flat contact housing / connecting part / distance sensor / F >> 89-H-520 000
2 pin /
flat contact housing / connecting part / distance sensor / F 89-J-100 001>>
3 pin /
flat terminal pin housing / for single wiring:
3 pin 000 979 127 000 979 218 000 979 407 / 1,0 2,5 6,0
flat contact housing / connecting part / 4 & 5-speed manual gearbox
5 pin /
flat contact housing / for single wiring: / rework if necessary / adapt with workshop equipment
35 pin 000 979 126 000 979 126 A 000 979 217 / 1,0 1,0 2,5
flat terminal pin housing / connecting part / starter
1 pin / PS
flat terminal pin housing / connecting part / starter
1 pin /
relay plate / connecting part / oil pressure warning relay
9 pin /
grommet
28X10,7 /
harness for lambda probe
/
covering / wiring harness
lhd /
flat contact housing
6 pin /
flat connector housing / connecting part / dashboard
5 pin /
retainer / for vehicles with hydraulic brake servo
/
washer
6,4X18X1,6 /
hexagonal nut
M6 /
no longer available
/
hexagonal head bolt
M8X15 /
washer
A8,4X16X1,6 /
retainer / connecting part / anti-knock sensor
lhd /
retainer / connecting part / anti-knock sensor
rhd /
washer
A6,4X12,5X1,6 rhd /
hexagonal nut
M6 rhd /
cable holder / connecting part / brake booster
rhd /
grommet
8,5 /
grommet
10X32 /
grommet
56,5/15 /
grommet
27X48 /
flat contact housing with helper contact catch and grommet / connecting part / for models with onboard computer / F 89-K-000 001>>
4 pin /
flat contact housing / connecting part / temperature sender
4 pin /
flat terminal pin housing
1 pin /
flat connector housing / connecting part / dashboard
10 pin /
weld pin 'order unit 100'
5X12 /
flat terminal pin housing / connecting part / ground strap
1 pin / NG
round connector housing
2 pin / PS
rd. connector sleeve housing
2 pin /
grommet
/
grommet
12,5X31 /
protective cap / connecting part / distance sensor / F 89-J-100 001>>
/
protective cap
16X25 /
flat contact housing / connecting part / for diagnosis plug / F 89-K-000 001>>
2 pin white /
flat contact housing / connecting part / for diagnosis plug / F 89-K-000 001>>
2 pin black /
flat contact housing with helper contact catch and grommet / connecting part / wiring harness: rear / air conditioner / relay
2 pin /
flat contact housing with helper contact catch and grommet / connecting part / air conditioner / relay
1 pin /
flat contact housing with helper contact catch and grommet / connecting part / wiring harness: front left
3 pin /
flat contact housing with helper contact catch and grommet / connecting part / on-board computer
4 pin /
flat contact housing
8 pin /

Last forum topics about this model
I have an old Audi 80 - year model 1987 - still going strong, but I have one problem:

Sometimes - usually after driving more than an hour - it refuses to start again. It doesn't make any sound.

Then after maybe half an hour it starts normally.

It is quite unpleasant because I have no idea, why it does that ( =doesn't start)

I have a new starter, new cables to the starter, new ignition key system...

After replacing practically everything between the ignition key and the starter motor I found a relay, which is called "relief terminal relay".

Somebody told me that it is also so called x-contact relay, which has many purposes.

Could anybody tell me the meaning of this relay?

Could it be the cause for that mysterious starting problem?

It would be nice know if somebody else has had this problem...

Posted by hangab (Finland) 2008-09-04 22:22:35 AUDI Audi 80/90/AvantComments: 2, last 2008-11-17 12:38:46Open thread »»

Hi!
I have problem.
I cannot open my rear door using the handle.
The handle is not tensed anymore and it is soft(you can pull in order to open the trunck but with no result)

I put out the inner door ornament in order to see the mechanism.
Now... my big problem is... how should it be correctly assebled?
I looked on http://www.vagcat.com/epc/cat/au/A80/1994/150/56/1612769/ but i did not understand much.

Can you give me some info about what should i do to repair it?

Thanks!
razvan.c.radulescu@gmail.com

Posted by rcrazvan (Romania) 2008-08-22 20:14:30 AUDI Audi 80/90/AvantNo comments yet ...Open thread »»

Hi to you all. I hope somebody can help me? My Audi is a 1994 model 80 TDi.
The speedometer has stopped registering mileage done. Can someone tell me which sensor I need to replace and where is it situated? This is a fantastic site, I only wish it could add where some of the elusive parts are on the car. I thank you all in advance.
Johnro

Posted by johnro (United Kingdom) 2008-08-21 02:13:38 AUDI Audi 80/90/AvantComments: 2, last 2008-08-23 19:28:11Open thread »»

Where can I find a Non-return valve?
Pierburg Part#: 041.906.291.A

Posted by shogun (United States) 2008-08-05 03:04:56 AUDI Audi 80/90/AvantNo comments yet ...Open thread »»

Hi, I have an Audi 80 -94, with a few problems related to the cooling system:

1. The water in the expansion tank is completely cold even after 30 minutes of driving (not sure when this problem started). The radiator seems to have normal temperature.

2. Also the warning lamp is flashing all the time (this appeared a few days ago).

3. The fan always run when the ignition is on (these has been a fact for a year or so). I believe I should just exchange the thermo-switch?

I have an oil temp meter saying it's about 70C (158F 431K) and when touching the engine it seems to have normal temperature.

So it's probably two different faults (or maybe three). I tried yesterday to exchange the expansion tank, with the water level switch, with no success.

Regards Magnus

Posted by BlombergM (Sweden) 2008-03-08 17:12:16 AUDI Audi 80/90/AvantComments: 2, last 2008-03-10 10:07:22Open thread »»